Product Introduction
The XGS20ACK is a high-performance electric straight boom aerial work platform. Powered by battery, it features zero emission, low noise and stable operation. With a maximum working height of 20.5m and rated load of 300kg, this model delivers excellent outreach and flexible maneuverability. It is widely applied for outdoor construction, municipal maintenance and indoor high-altitude operations, serving as a reliable solution for various aerial working demands.
Product Advantages
Large Working Range: Max working height 20.5m and max horizontal outreach 13.2m, covering long-distance high-altitude work.
High Load Capacity: 300kg rated load, supports 2 operators plus working tools for higher efficiency.
Eco-friendly Power System: Full electric drive, no exhaust and low noise, suitable for enclosed and environment-sensitive areas.
Strong Trafficability: 45% gradeability, 4-wheel drive and axle balance design, adapts to rough roads and sloped terrain.
Flexible Rotation: 360° continuous turntable rotation and 160° platform swing, realizing all-round positioning without dead angles.
Smooth Movement: Load-sensing hydraulic system ensures steady boom movement and energy saving.
Durable Driving System: AC drive and differential steering reduce tire wear and extend service life.
Product Specifications
Item | Unit | XGS20ACK | XGS20ACK-Li |
Max. Working Height | m | 20.5 | 20.5 |
Max. Platform Height | m | 18.5 | 18.5 |
Max. Horizontal Outreach | m | 13.2 | 13.2 |
Rated Platform Capacity | kg | 300 | 300 |
Platform Dimension | mm | 1830×760×1150 | 1830×760×1150 |
Overall Dimension (L×W×H) | mm | 9800×2490×2640 | 9800×2490×2640 |
Total Weight | kg | 8600 | 8350 |
Power Source | - | 48V 400Ah Lead-acid Battery | 51.2V 412Ah Lithium Battery |
Travel Speed | km/h | 0-4.8 | 0-4.8 |
Max. Gradeability | % | 45 | 45 |
Turntable Rotation Angle | ° | 360° Continuous | 360° Continuous |
Platform Swing Angle | ° | 160 | 160 |
Boom Luffing Angle | ° | -65 ~ +70 | -65 ~ +70 |
Outer Turning Radius | m | 5.0 | 5.0 |
Max. Tail Swing | mm | 1630 | 1630 |
Application Scenarios
Municipal Engineering: Street lamp, traffic signal and bridge inspection & maintenance.
Large Venues: Roof maintenance, lighting and audio equipment installation for stadiums, exhibition centers and airports.
Industrial Plants: Steel structure installation, pipeline and mechanical equipment maintenance, high-level cleaning.
Building Construction: Exterior wall construction, glass curtain wall installation and overhead operation.
Power & Landscaping: Tree trimming, power line and photovoltaic equipment maintenance.
Commercial Places: High-altitude cleaning and decoration installation for shopping malls, hotels and lobbies.
Operation Guide
Pre-operation Inspection
Check battery power, ensure sufficient electricity for work.
Inspect tires for normal pressure and no damage.
Verify hydraulic oil level and no fluid leakage.
Check guardrails and platform door to make sure all safety locks work properly.
Operating Steps
Turn on the main power and wait for system self-check completion.
Drive the machine to the working area and engage parking brake.
Operate control levers to lift, extend and rotate the boom slowly to the target position.
Fine-tune the platform angle for accurate positioning.
After work, retract the boom to stowed position first, then cut off the power.
Safety Rules
Never overload the platform; maximum 2 persons on board.
Operate only on firm ground, ground slope shall not exceed 5°.
Stop working immediately when wind speed exceeds 12.5m/s.
Wear safety helmet and safety harness during high-altitude operation.
Inspect safety sensors and limit devices regularly to guarantee normal function.
FAQ
Q1: What is the difference between XGS20ACK and XGS20ACK-Li?
A: They adopt different power batteries. XGS20ACK is equipped with lead-acid battery, which is cost-effective and easy to maintain. XGS20ACK-Li uses lithium battery, featuring lighter weight, longer service life, faster charging and longer working duration, ideal for frequent and long-time operation.
Q2: What about the working time and charging time?
A: The lead-acid version can work continuously for 4-6 hours, with full charging time of 8-10 hours. The lithium version supports 6-8 hours continuous work, and can be fully charged within 2-3 hours with fast charging.
Q3: Can this machine be used indoors?
A: Yes. Full electric design produces no exhaust gas and low noise, which is perfectly suitable for indoor working environment.
Q4: What is the maximum climbing capacity?
A: The standard gradeability is 45%. Equipped with 4-wheel drive and axle balance system, it can run stably on muddy, gravel and sloped roads.
Q5: Is customization available?
A: Yes. We support customized platform size, guardrail height and body color. Optional fast charging interface and remote monitoring system are available for lithium battery model.
Q6: What is the warranty policy?
A: The whole machine is warranted for 12 months or 2000 working hours (whichever comes first). The lithium battery enjoys 36 months warranty, and core components provide long-term maintenance service.
